Cảm biến Banner U-GAGE T30UX

  • Tel: 08-62974701 - 02 - 03 
  • Fax: 086297474  
  • Hotline: 0903 733 151  - 0983 533 151  
  • Email: thaibinhdhl@gmail.com 
Đặt hàng
Sensing Range Models ending in A:100 mm to 1 m (3.9 in. to 39 in.)
Models ending in B:200 mm to 2 m (7.8 in. to 78 in.)
Models ending in C:300 mm to 3 m (11.8 in. to 118 in.)
Ultrasonic Frequency Models ending in A:224 kHz
Models ending in B:174 kHz
Models ending in C:114 kHz
Supply Voltage 10 to 30V dc (10% max. ripple) at 40 mA, exclusive of load
Supply Protection Circuitry Protected against reverse polarity and transient voltages
Output Configuration Analog Output: 0 to 10V dc or 4 to 20 mA, depending on model
Output Rating Analog Voltage Output:2.5 kΩ min. load resistance Minimum supply for a full 10V output is 12V dc (for supply voltages between 10 and 12, V out max. is at least V supply -2)
Analog Current Output:1 kΩ max. @ 24V input; max. load resistance = (Vcc-4)/0.02Ω
For current output (4-20 mA) models:ideal results are achieved when the total load resistance R = [(Vin – 4)/0.020]Ω. Example, at Vin = 24V dc, R ≈ 1 kΩ (1 watt)
Output Protection Circuitry Protected against short circuit conditions
Output Response Time Models ending in A:45 ms (fast); 105 ms (slow)
Models ending in B:92 ms (fast); 222 ms (slow)
Models ending in C:135 ms (fast); 318 ms (slow)
Delay at Power-up 500 ms
Temperature Effect 0.02% of distance/ºC
Linearity 0.25% of distance
Resolution Models ending in A:0.1% of distance (0.5 mm min.)
Models ending in B:0.1% of distance (1.0 mm min.)
Models ending in C:0.1% of distance (1.5 mm min.)
Sensing Hysteresis Models ending in A:2 mm
Models ending in B:3 mm
Models ending in C:4 mm
Minimum Window Size 10 mm (0.4 in.)
Adjustments Sensing window limits:TEACH-Mode configuration of near and far window limits may be set using the push button or remotely via TEACH input
Response speed selection:Fast or Slow
Advanced configuration options:Analog output slope, push button enabled/disabled, temperature compensation enabled/disabled
Loss of Signal Indication 0 to 10V dc models:Analog output goes to 0V
4 to 20 mA models:Analog output goes to 3.6 mA
Construction Housing:PBT polyester
Push buttons:polyester
Transducer:epoxy /ceramic composite
Environmental rating Leakproof design, rated IEC IP67 (NEMA 6)
Connections 2 m (6.5 ft.) or 9 m (30 ft.) shielded 4-conductor (with drain) PVC cable, 150 mm (6 in.) PUR Euro-style pigtail (QPMA), or 4-pin integral Euro-style connector (Q8)
Operating Conditions Temperature:−40 to 70º C (−40 to +158º F)
Max. Relative Humidity:95% at 50ºC non-condensing
Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max., double amplitude 0.06 in., max acceleration 10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave
Application Note The temperature warmup drift upon power-up is less than 1% of the sensing distance.
Certifications CE Pending



Sản phẩm cùng loại

Danh mục



Lượt truy cập

Hôm nay
Hôm qua
Tuần này


Trụ sở: 97/4 KP.2, P. Thới An, Q.12, TPHCM

    VPGD: 32/1 Lê Văn Huân, P13, Q.Tân Bình, TPHCM

028.6297.4701 / 702 / 703


Thống kê truy cập

Hôm nay
Hôm qua
7 ngày qua
Lượt truy cập: